Nitro Rc Top Speed
Nitro RC Car Gearing
Introduction – Nitro RC Car Gearing
All nitro powered radio control trucks or cars require gearing. Gearing allows the change in RPM to better suit what is needed at the wheels. For example a typical Nitro engine can rev up to or past 30 000 RPM. The wheels however usually rotate at a much smaller rate. The way this is achieved is by gear reduction.
On road cars have smaller tires and travel at higher speeds. Gear ratios in these cars will be lower than average.
Monster Trucks have larger tires and travel at slower speeds than on road vehicles requiring higher gear ratios.
Nitro RC Car Gearing – Mesh
Gear Types – Nitro RC Car Gearing
There are two typical gear types found in RC Cars or Trucks. These are often referred to as the pinion gear and spur gear. The pinion gear is usually composed of around 15 teeth and made from a metal material. This pinion gear is placed on a clutch bell that is attached to the crank shaft of the nitro engine. A spur gear is commonly made from a nylon material. Spur gears tend to be around 45 teeth. The two different types of material cause minimal radio interference and ultimately create a quieter gearing mesh.
Gearing Mesh – Nitro RC Car Gearing
It's important to properly set the mesh between your pinion gear attached to the clutch bell on your motor with the spur gear located on the transmission of the RC car or truck. A common method of properly adjusting gear mesh is to place a piece of lined standard paper between the pinion and spur gear. Carefully press the two gears together firmly to squeeze the paper matching the shape to the gears. This properly provides the couple millimeters of clearance that is required in the rc car gearing.
Secure the nitro engine in place. It is highly recommended to use Loc-Tite for this process. It is critical for the fasteners securing the nitro engine to not loosen during operation. If they do loosen the gearing mesh clearance will grow increasing the chances of stripping the rc car gearing. If not caught immediately it does not take long until this may occur and once it vibrates loose to a certain extent, stripped gear occurs instantly.
Gear Ratio's – Nitro RC Car Gearing
Gear ratio's in the nitro rc car gearing are typically provided with some limitations. The transmission itself in the nitro car or truck is set permanently. The only options that are common for choice of gear ratio is in some cases the spur gear and in all other cases the clutch bell pinion gear.
When given the opportunity to select the best pinion gear to provide the desired performance, it is important to keep a few things in mind.
A larger pinion with more teeth will decrease the gear ratio.
A smaller pinion with less teeth will increase the gear ratio
A larger gear ratio will provide increased acceleration and a better power-band in rougher terrain. It's overall top speed will be reduced
A smaller gear ratio will be the exact opposite. It will suffer in acceleration performance, have a more difficult time in rougher terrain and will have increased top speed.
It's also important to understand there are limits to setting the gear ratio outside of what pinions are actually provided. Let's say for example we can have the largest pinion custom made. What has already been said above, tells us that this should provide the highest top speed.
See the RC Car Calculator to predict how gearing changes top speed.
While this is true on paper, the lower gear ratio from the largest pinion size will provide the highest theoretical top speed. This may not be true in reality.
The motor must produce enough power to handle the extra load. If the gear ratio is set too low, it will probably not even reach the speeds that a high ratio would provide.
Remember to choose a balance between speed and acceleration. If your goal is speed, it may be wise to test out gear ratio's using one of the determining speed methods. The gear ratio that provides the highest speed is ultimately the best for that particular application. There is no real scientific way to determine this as there are several factors that lead up to the end result. Through calculations you may get close but not exact. Testing is recommended.
The RC Gearing Calculator helps determine the pitch.
Source: https://www.radiocontrolinfo.com/rc-cars/rc-nitro-cars/nitro-rc-car-gearing/
0 Komentar